SURLON GROUP / INDUSTRIES / RENEWABLE ENERGY
Powering a Sustainable Future
Renewable energy runs on two disciplines: materials that don’t
wear out, and metal that’s cut to the micron. Surlon Group supplies
both — Surlon India’s engineering polymers and Surlon Precision
Solutions’ aerospace-grade machining — from one integrated
group.
ONE RENEWABLE SUPPLY CHAIN
COMPLEMENTARY CAPABILITIES FOR RENEWABLE ENERGY
A wind turbine yaw system and a switchyard bracket ask for opposite things — a self-lubricating polymer, and a tolerance measured in microns. Surlon Group builds both in-house, so renewable OEMs and EPCs source a full component set from one group.
SURLON INDIA
ENGINEERING PLASTICS
Cast nylon, UHMW-PE, PEEK and PPS parts, in
production for wind turbines today.
↓ Products & Capability Below
SURLON PRECSION SOLUTIONS
PRECISION MACHINING
EN 9100 aerospace-grade CNC machining, ready to
bring the same tolerances to renewables.
HIGH-PERFORMANCE POLYMERS, PROVEN IN WIND.
Metal corrodes, seizes, and adds weight where it’s least wanted. Surlon India replaces it with cast nylon, UHMW-PE, PEEK and PPS parts engineered for yaw systems, gearboxes and nacelles — selflubricating, corrosion-proof, and built for two decades in the field, onshore and offshore.
INSULATION SLEEVE
DRIVE INLET SHAFT
YAW GREASE RESORVOIR
YAW RING BASE SCRAPPER
INSULATING SLEEVE
INSULATING SLEEVE 1
INSULATING SLEEVE 2
INSULATING BUSH
DISTANCE HEIBE
SPACER 1
AXIS
SLIDING RING
WHY POLYMER, NOT METAL
LIGHTWEIGHT
Improves energy efficiency and supports larger, more powerful turbines.
CORROSION-PROOF
No rust, no saltwater degradation — built for offshore.
THERMAL & ELECTRICAL
Stable insulation across extreme temperature swings.
DURABLE
Resists wear, stress and fatigue over a longer service life.
COST-EFFECTIVE
Lower maintenance and replacement cost over the turbine's life.
NOISE REDUCTION
Dampens vibrations, leading to quieter turbine operation.
SUSTAINABLE
Many of our polymers are recyclable, supporting eco-friendly designs.
LOW FRICTION
Materials offer low coefficient of friction and non – stick slip behaviour.
MECHANICAL STRENGTH
Mechanical strength to withstand high loads and dimension stability over a wide temperature range.
SELF-LUBRICATING
Light weight self-lubricating bearing material for extreme conditions.
PRECISION MACHINING FOR RENEWABLE ENERGY
SURLON PRECISION SOLUTIONS
Formerly Tata Precision Industries, Surlon Precision Solutions brings over 30 years of precision machining experience. Its CNC machining, metrology and surface finishing capabilities meet the demanding requirements of aerospace and defence and are now being applied to renewable energy components
EN 9100:2018
VMC / CNC FLOOR
PRCISION TURNED FLANGE
MACHINED BRACKETS & HOUSING
ENCLOSURES & HEAT SINKS
WHERE IT GOES ON THE TURBINE
BEARINGS & BUSHINGS
Heavy-load, high wear-resistant, thermally stable under extreme conditions.
GEARBOX COMPONENTS
Distributor rings cut friction and noise, extending gearbox life.
SEALS & GASKETS
Chemical resistance and durability for nacelle and gearbox sealing.
NACELLE HOUSING
Lightweight protection for sensitive control and electrical systems.
BENDING RESTRICTOR
Cable protection with high flexural strength and wear resistance.
THRUST WASHER, YAW BEARING
Self-lubricating, low-friction, available in large dimensions.
CABLE CLAMPS
Long life, corrosion resistant, low maintenance.
YAW SYSTEM WEAR PARTS
Slide plates, radial & axial plates, top plate, lower puck.
ENERGY ABSORPTION
Materials engineered to dampen impact — a complete material-to-system solution.
LOOKING AHEAD
ENGINEERING FOR A GREENER WORLD
The world is transitioning to clean, renewable energy. We are contributing with advanced materials and precision engineering that power a more sustainable tomorrow.
01
WIND ENERGY
Engineered plastic components that enhance performance, reliability and efficiency in wind turbine applications.
02
SOLAR ENERGY
Precision machined components for solar mounting systems and inverter housings—built for durability, efficiency and scale.